What are common problems with built up roofing?

Published by Anaya Cole on

What are common problems with built up roofing?

7 Common Roofing Problems

  • Flashings and Seams. With any roof – no matter what type – if you’ve got roof leaks, then you’ve got a problem.
  • Poor Installation and Unsatisfactory Workmanship.
  • Lack of Maintenance.
  • Ponding Water.
  • Punctures and the Addition of Penetrations Post-Installation.
  • Improper Repairs.
  • Blistering.

What is roof Alligatoring?

Roof Alligatoring Explained Roof alligatoring is the result of too much sun exposure. Over time, the sun’s rays can dry out the coating of a flat roof. The result is the rooftop begins to crack, and it looks similar to the skin of an alligator.

How long does Duro-Last roofing last?

between 15-30 years
There have been numerous Life Cycle Assessments on Duro Last roofing system and on average a PVC membrane roof like Duro Last can last anywhere between 15-30 years.

What material is Duro-Last?

Polyvinyl Chloride
What are Duro-Last Roofs? Duro-Last is a leading manufacturer of single ply PVC roofing systems – PVC stands for Polyvinyl Chloride. Duro-Last makes other durable roofing types including metal roofs and KEE membranes, however PVC membranes are their bread and butter.

What is the main cause of pitch pocket problems?

There are many reasons a pitch pocket fails. The sealer can dry out and shrink. Structural movement may also be to blame. If the penetration that is wrapped by the pitch pocket moves or vibrates, the pitch pocket seal could be compromised.

What causes a split in a roofing membrane?

3. Splitting. The most common splits occur when a metal accessory is flashed with a membrane material. As the temperature changes, metals and membranes expand and contract at very different rates.

Is Alligatoring on a roof a cosmetic issue?

In general, roof alligatoring is a sign that your roof is aging. That said, it is possible to prevent alligatoring, and to repair small patches before they get so bad that you have to replace your flat roof prematurely.

What causes blistering on roof?

Blisters are now usually formed when volatiles flash out of the asphalt in newly installed shingles. This is caused by excessive heat from poorly ventilated and over-heated roof systems. Blisters typically appear within the first year after shingles are installed.

What type of roof is Duro last?

thermoplastic single-ply roofing systems
Known as the “World’s Best Roof®”, Duro-Last, Inc. is the world’s largest manufacturer of custom-fabricated, thermoplastic single-ply roofing systems.

Is TPO better than EPDM?

TPO has better dimensional stability than EPDM. EPDM is more likely to shrink which can cause a variety of problems on your roof.

Is Duro-last PVC or TPO?

Duro-Last, Inc,. offers over three decades of proven PVC roof system performance with billions of square feet of membrane installed across North America.

What type of roof is Duro-last?

What do you fill a pitch pocket with?

Fill the entire pitch pocket/pan with the pourable sealer to provide a 100% waterproof, cured rubber seal. Note: Don’t fill the pitch pocket/pan with any foreign material (grout, insulation, granules, etc.). These fillers do not provide a watertight seal at the roof’s surface.

What can cause a failure in a roofing installation?

5 Most Common Roofing Installation Errors (Simple Guide)

  • Not Nailing Down Shingles Correctly.
  • Covering Over Old Materials.
  • Not Securing Your Roof’s Flashing.
  • Installing a Wrong Roofing Slope.
  • Having Inadequate Venting.

Why are my shingles bubbling up?

Asphalt shingles can blister as a result of trapped moisture in the shingles. In some cases, moisture can get trapped within the shingles during the manufacturing process. When the sun heats the shingle, the trapped moisture will rise to the surface, causing the tell-tale blistering.

Is duralast a TPO roof?

You might think that it is similar to Duro-last because of its name, but TPO is not a plastic roofing type. It is made of rubber composed of ethylene-propylene and polypropylene. TPO is single-ply, while Duro-last is multi-ply.

Is TPO roofing good for residential?

Easy Maintenance. Mold growth, punctures and tears, and the accumulation of dirt are practically non-existent with TPO roofing membranes. TPO roofs are flexible and allow for shifting or settling in the building. Even thermal expansions and contractions are readily accommodated by TPO roofing systems.

Where can I get a Duro-last roof in Phoenix?

Canyon State Roofing and Consulting is a trusted Phoenix roofing company specializing in Duro-last roofing. We offer roof repair and new roof installation for Duro-last and many other types of roofing in the Phoenix area. Call us today to meet with a roofing contractor and get an estimate for your property.

Why choose a Duro-last roof?

Duro-Last leads the roofing industry with comprehensive warranty coverage. Duro-Last was the first manufacturer with a warranty that expressly covers consequential damages on commercial buildings. We work hard and stand by every square foot.

How do I report an issue with my Duro-last roofing system?

If you already own a Duro-Last Roofing System, please call 866-284-9424 or click here to report an issue and request service.

What is Duro‐last X?

Duro‐Last®, Inc. Launches Duro‐Last X™: Industry’s First Custom‐Cut Roll Good Membrane Solution – Manufactured with the same formulation as the industry‐leading Duro‐Last membrane, Duro‐Last X is available in 10‐foot wide rolls that can be custom‐cut up to 200 feet in length.

Categories: FAQ